MATERIAL SAFETY DATA SHEET
SECTION 1: PRODUCT IDENTIFICATION
PRODUCT NAME: SAFEGUARD 30
PRODUCT USE: For use as a roofing underlayment
3400 sw 209th Ave Beaverton Oregon 97007
www.safeguard30.com – firstname.lastname@example.org – (503)-906-0768
SECTION 2: COMPOSITION INFORMATION ON INGREDIENTS
72% Asphalt, 15% Non-Woven Fabric, 13% Fiberglass
SECTION 3: HAZARDS IDENTIFICATION
This is not a hazardous product as defined by WHMIS
SECTION 4: FIRST AID MEASURES
SECTION 5: FIRE-FIGHTING MEASURES
FLAMMABILITY: Not flammable, but in case of fire, will contribute.
FLAMMABLE LIMITS IN AIR, UPPER: N/A
(% BY VOLUME) LOWER: N/A
FLASH POINT: N/A
METHOD USED: N/A
EXTINGUISHING MEDIA: Water spray and dry chemicals.
EXPLOSION HAZARDS: Not sensitive to impact or static discharge.
HAZARDOUS COMBUSTION PRODUCTS: Carbon Monoxide, Carbon Dioxide, Nitrogen Oxides
SECTION 6: HANDLING AND STORAGE
HANDLING AND STORAGE: Rolls should be properly restrained to prevent shifting during handling and storage
SECTION 7: PREVENTIVE MEASURES
LEAK AND SPILL PROCEDURE: N/A
RESPIRATORY PROTECTION: No respirator required under normal use
EYE PROTECTION: N/A
PROTECTIVE CLOTHING OR EQUIPMENT: N/A
SECTION 8: PHYSICAL AND CHEMICAL PROPERTIES
APPEARANCE: Black Woven Fabric.
ODOR: Minimal asphalt odor
PHYSICAL STATE: Solid
MATERIAL SAFETY DATA SHEET
BOILING POINT: N/A
MELTING POINT: N/A
FREEZING POINT: N/A
VAPOR PRESSURE (mmHg): N/A
SECTION 8: PHYSICAL AND CHEMICAL PROPERTIES (cont.)
VAPOR DENSITY (AIR = 1): N/A
SPECIFIC GRAVITY (H2O = 1): N/A
EVAPORATION RATE: N/A
SOLUBILITY IN WATER: Insoluble
PERCENT SOLIDS BY WEIGHT: 72% asphalt, 15% non-woven fabric, 13% fiberglass
SECTION 9: STABILITY AND REACTIVITY
INCOMPATIBILITY (MATERIAL TO AVOID): None
HAZARDOUS DECOMPOSITION OR BY-PRODUCTS: None
CONDITIONS TO AVOID: None
SECTION 10: TOXICOLOGICAL INFORMATION
TOXICOLOGICAL INFORMATION: N/A
SECTION 11: DISPOSAL CONSIDERATIONS
WASTE DISPOSAL METHOD: Check with local authorities for disposal instructions.
SECTION 12: TRANSPORT INFORMATION
U.S. DEPARTMENT OF TRANSPORTATION
PROPER SHIPPING NAME: N/A
HAZARD CLASS: N/A
SECTION 13: OTHER INFORMATION
DISCLAIMER: The information contained in this MSDS was compiled using the latest and most reliable information available to SAFEGUARD 30. The information is provided without any warranty, express or implied regarding its correctness or accuracy nor will SAFEGUARD 30 assume any liability for any loss or damage arising out of the use of this information including without limitation direct or indirect losses or expenses. To the extent permitted by law, no warranty express or implied regarding the product described herein shall be created by or inferred from any statement or omission from this MSDS . It is solely the responsibility of the user to determine safe conditions for use of this product and to assume liability for any loss, damage or expense whatsoever arising out of the product’s improper use.
• Special Notes:
1. Decks should be dry before application.
2. Unroll and use like regular asphalt felt underlayment.
3. Underlayment may be applied at any temperature that it is safe for the applicator to work.
4. Underlayment should be installed with Logo (SAFEGUARD30) facing up, SafeGuard 30 Can be left exposed if properly installed up to 180 days.
5. SAFEGUARD 30 fastening requirements:
a. Use 1″ minimum diameter plastic cap or 1″ minimum diameter or square metal head underlayment nails on 24″ centers on edges and 18″ centers in the field of the underlayment.
6.These are the minimum acceptable application instructions. More stringent requirements of the building codes should be followed. For further details, see the ARMA Residential Asphalt Roofing Manual.
• Standard Slope (4/12 and greater)
After the deck has been properly prepared, cover it with one layer of SAFEGUARD 30 underlayment. Lay the SAFEGUARD 30 parallel to the eaves, lapping each course at least 2″over the underlying course. If two or more pieces are required to continue a course, lap the ends at least 4″. End laps in succeeding course should be located at least 6′ (foot) from the end laps in the proceeding course. Lap the SAFEGUARD 30 6° from both sides over all hips, valleys and ridges. Where the roof meets a vertical surface, carry the SAFEGUARD 30 3” to 4″ up the surface.
• Low Slope (2/12 up to 4/12) and Tile Roofing
Cover the deck with two plies of SAFEGUARD 30 overlapping 19-1/2”. Begin by fastening a 19-1/2″ wide strip of SAFEGUARD 30 placed along the eaves. Place a full 37.25″ wide sheet horizontally along the eaves completely overlapping the starter layer. All succeeding courses will be minimum 37.25″ wide and should be positioned to overlap the proceeding course by 19-1/2″.
• Ice Dams
For all slopes, when there is a possibility of ice buildup along the eaves or a backup of water from pine needles or leaves, follow the above low slope guidelines to a point at least 24″ beyond the interior wall line of the building. Thoroughly cement between the layers using asphalt roofing cement conforming to ASTM D 4586. The cemented double ply underlayment serves as the eave flashing. After completing the eave flashing, secure each successive course as describe above in fastening requirements section until the final roof covering is applied.
Safeguard 30 LLC
P.: 1 (800) 563-1961
3144 SE TV Hwy. Hillsboro OR 97123
Serving in all Oregon, Washington, California, Beaverton, Lake Oswego, Sherwood, Tigard, West Linn, Wilsonville, Portland, Hillsboro, Gresham, Vancouver an the surroundings areas.